Call

Just about everyone maintains their personal rationale on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Installing a bathtub isn't specifically rocket science, however it does need strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old tub with a new one is additionally a reasonably challenging task. If the old tub is readily easily accessible, the job can relocate rapidly; if you have to open a wall to eliminate the old tub as well as position the brand-new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and also embeded in the brand-new one. Ensure you have qualified yourself for the work and fit trying it. Instead of hiring a service provider to take control of a halfway-completed job, it is far better to take into consideration utilizing one before you start. Opportunities are you might need an expert plumber to make tube connections.
This post will certainly aid you set up a new tub in your washroom if you have actually currently bought a new tub and also don't need to alter the arrangement of your previous water system pipelines.
Your devices as well as product list must make up the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Getting ready for the Installation

Firstly, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the adaptable tap ports to the bottom of the two faucets utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you use every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its final setting.

Removing Old Taps

If you need to change old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic because of the limited accessibility that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

Mounting the Bathtub

Utilizing both wooden boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by examining the level as well as readjusting the feet on the tub up until the level reads degree.
To mount taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Activate the water system as well as examine all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill up the tub and also examine the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bathtub should wait till the tub has actually been made use of at least once as this will settle it right into its last position.

Suitable New Touches

If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and the sink. Protect the tap in place with the manufacturer given backnut. Once the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous kind ought to be connected to the faucet ends initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

Tiling Around the Bath tub

In the location where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a rigid seal, creating the water to pass through the wall between the bath as well as the tiling, causing complications with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealer can split fairly early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof sticky and also grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you enjoy reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try leaving a remark further down. We would be interested to see your feelings about this entry. In hopes to see you back again later on. Are you aware of somebody who is inquisitive about the subject? Please feel free to promote it. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Overflow? We're here!